-
What is the difference between flat head rivet nut and small head rivet nut?
To put it simply, flat head rivet nuts, that is, those with thick heads, protrude outside the plate after riveting. Flat Head Rivet Nuts The small head rivet nut has a thin head. After riveting, it is flat outside the plate. Small Countersunk Head Rivet NutRead more -
What are the product characteristics of open round head blind rivets?
Open end round head core pulling rivet is a kind of fastener with high strength riveting. It has the characteristics of high strength, high finish, bright riveting surface, no rust points, stable and reliable riveting surface, flat riveting surface and so on. Open end round head blind rivets nati...Read more -
Application method of rivet gun II
5. Hold the handle with your right hand and press the button with your index finger to start the rivet gun. You can use the button to adjust the size of compressed air to ensure the smooth operation of the rivet gun. At the beginning of riveting, due to the long rivet rod and the large gap betwee...Read more -
Application method of rivet gun 3
6. The punch tail shall be prepared according to the models of different rivet guns and shall not be used in series to avoid damaging parts and reducing efficiency. 7.Do not empty the gun at will in use to avoid damaging the machine parts. 8.It is strictly forbidden to use the muzzle against peop...Read more -
Why does the blind rivet break the nail core rather than at the breakpoint of the pull nail?
1. The tension of the nail core itself is not stable, the breaking point force is very close to the tension of the nail core itself, or the heat treatment is not done well, and the nail core is brittle. 2. The nail core has been damaged before riveting. 3. The claw piece of the nail pulling gun i...Read more -
Application method of rivet gun I
1. Before starting work, inject a small amount of lubricating oil from the air inlet nozzle to ensure the working performance and service life of the rivet gun. 2. Maintain the specified intake pressure. If the air inlet pressure is too small, the power of the riveting hammer will be reduced. Not...Read more -
Dear new and old customers
The annual Lunar New Year is just around the corner. The Spring Festival is the beginning of the year in the lunar calendar. Another name is the New Year. It is the grandest, most lively, and most important ancient traditional festival in China. It is also a festival unique to the Chinese and the...Read more -
What is waterproof lantern rivet?
Waterproof lantern rivet is a structural rivet evolved on the basis of Lantern rivet. A rubber washer is added on the back of the hat brim to effectively play a waterproof role. During riveting, the nail core pulls the blind end of the pipe cap into three large lantern shaped folding strips to cl...Read more -
What is the reason for the fracture of aluminum blind rivets?
1. It is caused by external shear force after riveting; or the salad hole on the riveting plate is misaligned, causing the individual pull pin to bear too much force and roughly break. 2.Because the riveting plate has sharp burrs at the stamping hole, the rivet shell will be cut when the rivet sh...Read more -
How to remove pop rivets?
1. Cut off the tail of the blind rivet with diagonal pliers, and then use a small nail with the same diameter as the blind rivet to punch out the remaining blind rivet. It needs to punch out from the front, and finally punch out the cut rivet from the back 2. Pull off pop rivets shall not be shav...Read more -
What is a lantern rivet?
Lantern rivets: When the lantern rivet is riveted, the nail core pulls the blind end of the pipe cap into three large lantern shaped folding strips to clamp the two components to be riveted. It is widely used in thin, soft and brittle parts such as household appliances, caravans and recreational ...Read more -
What are the advantages of lantern rivets?
1. Wide riveting range. 2. The lantern shaped tail provides a large bearing surface and disperses the force on the riveted parts. It is an ideal choice for riveting thin plates or low-strength materials. 3. High clamping force and large bearing surface at the blind end can effectively prevent the...Read more